車徐州NSK軸承使用維護說明書摘要：在額定載荷范圍內嚴重過載直接導致軸承過載過早失效，導致汽車故障、人身安穩事故、禁止軸承異常沖擊載荷、定期檢查軸承運行狀態、注意軸承磨損。軸承零件有異響，是否有局部急劇溫升現象。定量的流體動力和流體靜力學軸承需要定期安裝。

Xuzhou NSK bearing operation and maintenance instructions abstract: Serious overload within the rated load range directly leads to premature failure of bearing overload, leading to automobile failure, personal safety accident, prohibition of abnormal impact load bearing, periodic inspection of bearing operation status, attention to bearing wear and tear. Bearing parts have abnormal sound, whether there is a local sharp temperature rise phenomenon. Quantitative hydrodynamic and hydrostatic bearings need to be installed regularly.

汽車軸承的使用和維護：

Use and maintenance of automobile bearings:

（1）車輛應在額定載荷范圍內工作。如果過載嚴重，將直接導致軸承過載，從而導致軸承早期失效。更嚴重的是，徐州NSK軸承會導致車輛故障和人身安穩事故。

(1) Vehicles shall work within the rated load range. If the overload is serious, it will directly lead to the bearing overload, which will lead to the early failure of the bearing. More seriously, Xuzhou NSK bearings will lead to vehicle failure and personal safety accidents.

（2）禁止軸承承受異常沖擊載荷；

(2) It is forbidden for bearings to bear abnormal impact loads;

（3）定期檢查軸承的使用情況，注意軸承部位是否有異常噪音和局部溫升急劇。

(3) Check the use of bearings regularly, and pay attention to whether there is abnormal noise and sharp local temperature rise in the bearing parts.

（4）按要求定期定量注入潤滑油或潤滑油；

(4) regular and quantitative injection of lubricating oil or lubricating oil as required;

（5）根據車輛使用情況，每半年至少更換一次潤滑油，并仔細檢查軸承。

(5) According to the use of vehicles, at least once every six months to replace the lubricant, and carefully check the bearings.

（6）徐州NSK軸承的大修檢查：用煤油或汽油清洗和解體軸承，仔細觀察軸承內外圓柱面有無滑動或爬行，軸承內外滾道有無剝落或點蝕，滾動體和保持架有無磨損（bASIC失效形式為CO）。（a）構件變形和軸承綜合檢查的確定。我們能繼續用嗎？

(6) Overhaul inspection of NSK bearings in Xuzhou: cleaning and disassembling bearings with kerosene or gasoline, carefully observing whether the inner and outer cylindrical surfaces of bearings slide or creep, whether the inner and outer raceways of bearings peel off or pit corrosion, whether the rolling bodies and cages wear (bASIC failure form is CO). (a) Deformation of components and determination of comprehensive inspection of bearings. Can we continue to use it?

（7）工業軸承是精細零件。注意使用。即使高性能軸承使用不當，也不能達到預期的性能效果，容易造成軸承損壞。

(7) Industrial bearings are fine parts. Pay attention to the use. Even if the high-performance bearings are used improperly, they can not achieve the expected performance effect, which is easy to cause bearing damage.

（8）徐州NSK軸承具有額定負荷高、噪音低、維護成本低、運行時間長的優點。在識別真軸承或假軸承時，可通過觸摸軸承上的鋼印更快、更準確地識別軸承。用手觸摸郵票時不會觸摸它，但輕輕觸摸釘子可以感覺到郵票的存在。

(8) Xuzhou NSK bearings have the advantages of high rated load, low noise, low maintenance cost and long running time. When identifying true or false bearings, the bearings can be identified more quickly and accurately by touching the steel stamps on the bearings. The stamp will not be touched when touching it by hand, but the existence of the stamp can be felt by touching the nail lightly.

文章來自：徐州SKF軸承 www.wh-skf.com

Article from: Xuzhou SKF Bearing www.wh-skf.com

文章來自：徐州INA軸承 www.ina-china.cn

Article from: Xuzhou INA Bearing www.ina-China.cn

文章來自：徐州NSK軸承 www.klbbearings.com

Article from: Xuzhou NSK Bearing www.klbbearings.com

QQ：524085168

電話：0510-81207777

手機：13311666672/13395185757